Upward-firing wireless speaker create 5.1.4 3D sound


ONEmicro+ is an upgraded version from ONEmicro particular design for 5.1.4 surround height channel speaker. ONEmicro+ is up-firing speaker can be on position TF (Top Front), TM (Top Middle) or TR (Top Rear). 2 pieces ONEmicro+ as TM speaker can generate a 3D sound space, from 2 dimensional 5.1 sound turn to 3 dimensional theatre surround. If you have 4 pieces ONEmicro+, put them at 4 corners, you will hear sound objects moving in 3D position, heightened sound space bring you superb sensation.

ONEmicro+ is use state-of-art 3D algorithm to create horizontal and vertical sound space, re-build sound object renderings, positioning sound objects in 3D space.  You can listen sound object anywhere in 3D space and sound objects moving are over your head.

No matter sound source is Dolby Atmos, DTS-X or basic 5.1 sound, the AIR+ can turn 5.1 2D sound to 5.1.2/5.1.4 3D sound. From now on, classic movies, drama movies, online movies, all will have 3D sound, transport you to realistic movie story.  Imagine you will hear a bird flying in the sky, you will sense a hallow echo in a cave.

ONEmicro+ is more advances

ONEmicro+ and ONEmicro have same look and same form factor. Inside ONEmicro+ is equipped with more powerful SOC chip, double speed to handle sophisticated 3D algorithm. Due to processor changed, ONEmicro can’t be upgrade to ONEmicro+.

  • Boosted DSP to deliver more computation power
  • High capacity battery which is 20% more than ONEmicro
  • Higher frequency response up to 32KHz to create airy sound space with height
  • Multi-channel receiver, extract sound object in front and rear channel, then re-render sound object model
  • Dynamic propagation time alignment for TF, TM and TR speaker

How to use ?

  • Additional 2 pieces ONEmicro+ to 5.1 surround set, configure as TML and TMR speaker upgrade to 5.1.2
  • Additional 4 pieces ONEmicro+ to 5.1 surround set, configure as TFL, TFR, TRL and TRR speaker upgrade to 5.1.4
  • 2 pieces ONEmicro+ add on 3.1 set, upgrade configure to 3.1.2 as TRL and TRR speaker
  • Additonal 2 pieces ONEmicro+ to 2.1 stereo set, configure as AIR+ top sepaker to enable AIR+ 3D function
  • As a rear speaker for stereo play,  ONEmicro+ can be AIR+ rear speaker or stereo speaker parallel to main speaker
  • Standard speaker as of ONEmicro, can use ONEmicro+ to build 2.0 stereo set or 5.1 surround set

Specification :

Size  :  Φ62 x 54(h)  mm
Weight  :  0.7Kg / pair
Colour  :  White, Black
Output power  :  5.5W / pair
Freq. response   :  68-32000Hz
Driver  :  Full range 48mm neodymium magnet, outter bass radiator
Audio mode  :  Stereo, surround, vocal, TV, AIR+ 3D, AIR+ Surround
Position  :  Main, Rear, Centre, Top front, Top middle, Top rear
Play time  :  25 hours for stereo play or 15 movies watch
Charge time  :  4 hours by 5V 1A

How to create 3D surround sound ?

ONEmicro+ is up-firing design. You don’t need to hang them up, place them at relative high position, or just put them on main speaker or rear speaker top. For 5.1.2, try to put them at left and right side of listener. For 5.1.4, place them at 4 corners.

  • 5.1.4, add into ONEclassic 5.1, ONEmedi 5.1, Combo 5.1 set as TF and TR speaker
  • 5.1.2, add into ONEmini 5.1 set as TM speaker
  • 3.1.2, add into ONEmini 3.1 or Combo 3.1 set as TR speaker
  • AIR+ stereo, add into stereo set as rrear speaker
  • Standard stereo, connect to ONEdongle or ONEbox.micro as L and R speaker

 


How to setup ONEmicro+ TOP speaker

Setup is so simple, no complicate calibration procedure. Just input 2 position settings in WebUI top sepaker setup page.

  • Set speaker placement height
    * Speaker top : on front or rear speaker top
    * Half height : on listener ear level 
    * Ceiling : high position near ceiling
  • Set rear speaker position
    * Seating side : next to your seating place
    * Halfway : in between seating and rear corner
    * Corner : rear corner of your room